Skip to main content

PoE Adapter

Power your Minut M3 sensor and connect it to the network over a single Ethernet cable: no Wi-Fi setup, no batteries, no charging.

Written by Emilie Pain

What's in the box

Item

Details

PoE Adapter

IEEE 802.3af RJ45 input. 5V DC 400mA USB-A output. 10/100 Mbps LAN pass-through. 35 × 37 × 23 mm.

Mounting bracket

108 mm diameter / 99 mm square. Fits standard EU/US ceiling junction boxes, or mounts directly to a structural surface.

USB cable

200 mm, USB-A to USB-C. Connects the adapter output to the USB-C charging port on the Minut M3 sensor.

Mounting screws

For securing the bracket to a ceiling junction box or structural surface.

Specifications

Input

IEEE 802.3af Power over Ethernet, 37–57V DC via RJ45

Output

5V DC, 400mA, USB-A port

Network

10/100 Mbps Ethernet, Auto MDI-X via RJ45 pass-through

PoE standard

IEEE 802.3af. Requires a PoE-capable switch or injector.

Adapter dimensions

35 × 37 × 23 mm

Mounting bracket

108 mm diameter / 99 mm square. Fits standard EU/US ceiling junction boxes.

USB cable

200 mm, USB-A to USB-C. Minut M3 sensor only.


When to use the Minut PoE Adapter

Use the Minut PoE Adapter when your building has managed Ethernet and you want to remove both battery charging and Wi-Fi dependency in one installation.

Best for

Multifamily, student housing and hotel deployments where managed Ethernet runs are available at each unit or room.

Wi-Fi not required

The sensor connects to the network through the Ethernet cable, so you don't need a Wi-Fi password during installation. The sensor can also use Wi-Fi as a fallback if you prefer.

IT network

Suits buildings where IT policy requires devices to be on a managed wired network. Make sure ports 25500 (TCP), 1993 (UDP) and 443 (HTTPS) are open outbound.

vs AC Power Adapter

If you only need continuous power and Wi-Fi is reliable, the Minut AC Power Adapter is an alternative. Use PoE when you want power and a wired network in one cable.

Installation

Check that your switch supports IEEE 802.3af before you start. A standard (non-PoE) switch will not power the adapter.

The USB cable is 200 mm (about 20 cm). Plan the mounting position so the adapter sits within 20 cm of the sensor: inside the ceiling void, in the junction box, or surface-mounted next to the bracket.

  1. Run the Ethernet cable to the mounting location
    Route a Cat5e or Cat6 Ethernet cable from a PoE-capable switch port to the installation location. Maximum cable run: 100 m per segment.

  2. Mount the bracket
    Secure the mounting bracket at your chosen ceiling or wall location with the included screws. The bracket fits standard ceiling junction boxes or can be fixed directly to a structural surface.

  3. Connect the Minut PoE Adapter
    Plug the Ethernet cable into the RJ45 input port on the adapter. Connect the USB-A to USB-C cable from the adapter's USB-A output to the USB-C port on the back of the Minut M3 sensor.
    The sensor turns on automatically once the Ethernet cable delivers PoE power.

  4. Pair the sensor in the Minut app
    Tap Properties at the bottom of the screen and select your unit. Tap the + icon in the Devices section and select Minut M3. When the sensor glows purple (setup mode), tap Continue and select Indoor mode to finish pairing. The sensor already has network access through the adapter, so there is no Wi-Fi step.
    ​The mode setting is permanent and can't be changed after installation.

  5. Attach the sensor and confirm
    Snap the Minut M3 sensor onto the mounting bracket (it attaches magnetically). It uses the wired Ethernet connection for network access.
    ​Green light = online and monitoring.

MAC address for network allow-lists. If your building uses device access controls, you may need to allow the Minut M3 sensor's MAC address. You'll find it on the label on the back of the sensor, or in the app under Properties → your unit → sensor → ⚙ → Advanced.

Already have the sensor installed? Use Sensor Swap to move its settings and data to the newly wired sensor without a full reinstall.

Battery protection mode

When the Minut M3 sensor is permanently powered through PoE, it automatically switches to battery protection mode. It holds the battery slightly below full to avoid wear from continuous charging. This is normal.

What you may notice

The battery level in the app may show 80–90% rather than 100%, even while permanently powered.

Is monitoring affected?

No. All features work normally.

Low battery alerts

Won't trigger for a permanently wired sensor.

Compatibility

Compatible sensors

Minut M3 sensor only. Not compatible with the Minut M2 sensor or the Minut E1 sensor (the Minut E1 sensor has its own power options).

PoE switch required

An IEEE 802.3af compliant PoE switch or PoE injector. Standard (non-PoE) switches won't power the adapter.

Indoor only

For indoor installations only. Not recommended for sensors in outdoor mode.

Purchase

Available at store.minut.com. Select the PoE Adapter kit at checkout.

Did this answer your question?